Banner
Navigation

Navigation

loco-info.com
The reference for locomotives and railcars

London, Midland & Scottish Horwich Mogul “Hughes Crab”

London, Midland & Scottish class 5MT

Great Britain 1926 70 produced
42831 at Balornock flickr/stratfordman72

The Horwich Mogul takes its name from the LMS works in Horwich, formerly Lancashire, where the first batch of these locomotives was built. However, it is better known by the name “Hughes Crab” given to her by rail enthusiasts. In order to accommodate the large cylinders within the loading gauge, engineer George Hughes was forced to incline them and set the connecting rods a few degrees upwards. Since this gave the impression of a crab with its claws, it was given this name. It was designed taking into account the latest knowledge and planned with the most modern assemblies available in terms of brakes, valves, boiler and tender. The design was only implemented under Henry Fowler and it was initially questionable whether all the innovations could actually be put into practice.

Due to the technical progress, however, it was possible to implement a large part of the innovations, while standard parts of the LMS only had to be used for the brake system and the boiler attachments. A standard model from Derby Works was used as the tender. Since the locomotive itself made full use of the available loading gauge and this was not the case with the tender, the latter was noticeably narrower than the locomotive's cab. A total of 70 were built at Horwich and a further 175 at Crewe between 1926 and 1932. These engines were particularly popular in Scotland on the mountainous routes when used in front of heavy ore and coal trains without continuous brakes.

Over time, some locomotives have been experimentally upgraded with modern parts. In 1934, five received Lentz valve gear, which they also kept. However, it stayed with these five. In 1954 a new chimney including a new blastpipe was tested on one locomotive. This increased the boiler's evaporative capacity by 25 percent, but it remained a one-off. The locomotives were retired between 1961 and 1967 and three remain in existence today. 13065 was preserved in operational condition and operated until 2018 when several faults were discovered in its boiler.

42894 in 1951 at Bescot Depot Ben Brooksbank / Hughes/Fowler 2-6-0 at Bescot Locomotive Depot / CC BY-SA 2.0

Technical data

General

Built
1926-1932
Manufacturers
Horwich, Crewe
Wheel arrangement
2-6-0 (Mogul)
Gauge
1,435 mm (Standard gauge)

Dimensions and weights

Length
18.06 m
Wheelbase
7.77 m
Service mass
66.6 t
Adhesion mass
56.4 t
Total mass
109.5 t
Rigid wheelbase
5.03 m
Axle load
18.8 t
Water capacity
15,910 l
Fuel capacity
5.1 t (coal)

Boiler

Grate area
2.555 m²
Firebox surface
14.865 m²
Tube heating surface
125.001 m²
Evaporative heating surface
139.866 m²
Superheater surface
28.521 m²
Total heating surface
168.4 m²

Power plant

Driver diameter
1,676 mm
Boiler pressure
12.4 bar
Expansion type
simple expansion
Cylinders
two, 533 x 660 mm

Power

Power source
steam
Estimated power
858 kW (1,167 PS)
Starting effort
118.2 kN

Calculated values

Factor of adhesion
1 : 4.68
Optimal speed
45 km/h
Power-to-weight ratio
12.9 kW/t
Heating Surface Equivalent
271.2 m²
Cylinder volume/HSE
1 : 1,088.15
Adhesive weight/Total
1 : 1.18
Tractive force/Heating surface
1 : 14.66
Grate area/Heating surface
1 : 65.90
Firebox/Tube surface
1 : 8.41
Total/Superheater
1 : 4.90

Topics

  • steam locomotive
  • passenger
  • freight
  • George Hughes
CompareComment
Last changed: 01/2022

Watch on YouTube

Auf Deutsch umschalten

Settings

Your settings are retained for this browser session only.

Consent to cookies

We use cookies to save your display settings. If you decline, the settings are retained only for the current browser session.