Banner
Navigation
loco-info.com
The reference for locomotives and railcars

Paris-Orléans No. 4701 to 4712

Paris-Orléans 240-701 to 240-712 and French State Railway 4-240 A

France 1932 12 produced
collection William Vu

The numbers 4701 to 4712 of the PO were 4-8-0 express locomotives rebuilt by Chapelon from Pacifics of the 4501 to 4600 range in 1932 and 1933. The reason for the rebuild was that trains of 650 to 700 tonnes had to be accelerated to 120 km/h. He had already rebuilt the Pacifics 3701 to 3721 which now had much more power. On the other side, the adhesive weight of the three driving axles was still too small for heavy trains. So Chapelon decided to exchange the trailing axle against a fourth driving axle. To accomplish this, he now used a narrow and deep firebox instead of the original one with a trapezoidal layout.

Compared to the 3701 series, the steam lines were again enlarged and boiler pressure was increased from 17 to 20 bars. Like their predecessors, the 4-8-0 still had Nicholson thermic syphons and a double Kylchap exhaust. The valve gear was of the Lentz-Dabeg type and the diameter of the high pressure cylinders had been increased by 20 mm. These changes resulted in an output of 4,200 hp, with more than 3,000 hp available behind the tender. Although designed for 140 km/h, some problems with bogie centering and comfort in the cab were reported while running at the approved speed of 120 km/h.

In the following years, also the Nord, the État and the Est borrowed locomotives from this series for test service. However, no further locomotives of this design were ordered, but the SNCF ordered 25 of the similar 240 P in 1940. The older 4-8-0 locomotives had become 240-701 to 240-712 when the PO merged with the Midi in 1934. The SNCF designated them 4-240 A. Even later in their career, they still used the small three-axle tenders with eight tonnes of coal and 26 m³ of water due to many short turntables. The lines where they operated were electrified from 1943. Even though the northern and western divisions asked if they could used these locomotives, they were scrapped in 1952, like the 240 P.

Technical data

General

Built
1932-1933
Manufacturers
Tours
Wheel arrangement
4-8-0 (Twelve-wheeler)
Gauge
1,435 mm (Standard gauge)

Dimensions and weights

Length
20.32 m
Length loco
13.01 m
Wheelbase
10.00 m
Empty mass
97.8 t
Service mass
106.3 t
Adhesion mass
75.5 t
Total mass
163.7 t
Rigid wheelbase
6.00 m
Axle load
18.9 t
Water capacity
26,000 l
Fuel capacity
8 t (coal)

Boiler

Grate area
3.76 m²
Firebox surface
24.9 m²
Tube heating surface
191 m²
Evaporative heating surface
215.9 m²
Superheater surface
60.6 m²
Total heating surface
276.5 m²

Power plant

Driver diameter
1,850 mm
Boiler pressure
20 bar
Expansion type
compound
Cylinders
four, HP: 440 x 650 mm and LP: 640 x 650 mm

Power

Power source
steam
Indicated power
3,091 kW (4,203 PS)
Top speed
120 km/h
Starting effort
157.0 kN
Starting effort simple
188.5 kN

Calculated values

Factor of adhesion
1 : 4.71
Optimal speed
121 km/h
Power-to-weight ratio
29.1 kW/t
Heating Surface Equivalent
461.6 m²
Cylinder volume/HSE
1 : 881.22
Adhesive weight/Total
1 : 1.41
Tractive force/Heating surface
1 : 11.86
Grate area/Heating surface
1 : 73.54
Firebox/Tube surface
1 : 7.67
Total/Superheater
1 : 3.56
Auf Deutsch umschalten

Settings

Your settings are retained for this browser session only.

Consent to cookies

We use cookies to save your display settings. If you decline, the settings are retained only for the current browser session.