Banner
Navigation
loco-info.com
The reference for locomotives and railcars

Bavarian S 2/6

Germany 1906 1 produced
PD

The S 2/6 was a one-off that was only intended for testing higher speeds. It was ordered in December 1905 and developed and built within just four months. In terms of wheel arrangement and driving wheel diameter, it corresponds to the Prussian test locomotive S 9, with which high-speed tests had been undertaken shortly before. In contrast to this, however, the S 2/6 was otherwise based on near-series technologies.

In addition to the two coupled wheel sets with 2,200 mm wheels, the measures used in various places to reduce air resistance are distinguishing features of the locomotive. Other express locomotives of the time also had a cone-shaped smokebox door and a driver's cab tapered at the front, but there was a smooth transition from the boiler to the driver's cab. The streamlined cladding of the chimney, steam dome and cylinders went even further.

With a large grate area compared to other locomotives, a very good evaporation performance was obtained. Together with the four-cylinder compound engine, a calculated indicated output of up to 2,200 hp was achieved during test drives. On July 2, 1907, with four wagons with a total weight of 150 tonnes it traveled at a speed of 154.5 km/h. This value was a world record and caused a stir internationally.

Immediately after the test runs, the S 2/6 was put into regular use, where it was able to reach a speed of 120 km/h with trains weighing 360 tonnes. In operation in Bavaria, it was particularly unpopular with the planning staff because it was a one-off and its characteristics differed greatly from the other locomotives used. Compared to the S 3/6, the S 2/6 had more power, but with only two coupled axles it could generate less traction, which made planning the simultaneous use of both locomotives very difficult.

In 1910 the locomotive was relocated to the Palatinate network, which belonged to Bavaria, and was more popular there. On the Reichsbahn it would have become class 15, in which it would have been the only locomotive with a 4-4-4 wheel arrangement. However, after returning to Bavaria, it was decommissioned, refurbished and taken to the Nuremberg Transport Museum in 1925, where it is to this day.

Technical data

General

Built
1906
Manufacturers
Maffei
Wheel arrangement
4-4-4 (Reading)
Gauge
1,435 mm (Standard gauge)

Dimensions and weights

Length
21.13 m
Length loco
13.78 m
Wheelbase
11.70 m
Total wheelbase
18.50 m
Empty mass
74.8 t
Service mass
82.5 t
Adhesion mass
32.5 t
Rigid wheelbase
2.32 m
Axle load
16.3 t
Water capacity
26,000 l
Fuel capacity
7 t (coal)

Boiler

Grate area
4.7 m²
Firebox surface
16.5 m²
Tube heating surface
199 m²
Evaporative heating surface
215.5 m²
Superheater surface
37.5 m²
Total heating surface
253.0 m²

Power plant

Driver diameter
2,200 mm
Boiler pressure
15 bar
Expansion type
compound
Cylinders
four, HP: 410 x 640 mm and LP: 610 x 640 mm

Power

Power source
steam
Indicated power
1,620 kW (2,203 PS)
Top speed
150 km/h
Starting effort
85.9 kN
Starting effort simple
103.1 kN

Calculated values

Factor of adhesion
1 : 3.71
Optimal speed
116 km/h
Power-to-weight ratio
19.6 kW/t
Heating Surface Equivalent
373.0 m²
Cylinder volume/HSE
1 : 954.51
Adhesive weight/Total
1 : 2.54
Tractive force/Heating surface
1 : 7.09
Grate area/Heating surface
1 : 53.83
Firebox/Tube surface
1 : 12.06
Total/Superheater
1 : 5.75
Auf Deutsch umschalten

Settings

Your settings are retained for this browser session only.

Consent to cookies

We use cookies to save your display settings. If you decline, the settings are retained only for the current browser session.